Welding A Sheet Metal Hull - Tracked Amphibious Vehicle Build Ep. 16

  Vaatamised 473,338

Donn DIY

Aasta tagasi

Latest video: eepost.info/my/video/o2-LdnVnopKFuos.html
MIG/MAG welding the bottom half of the tracked amphibious vehicle's hull sheet metal and hopefully making it watertight in the process. The drainage bolts are not welded in yet and the seals are also not in the rear wheel hubs yet. But other than that - this hull should already float like a boat. I will cut an additional hole in the rear for a specific purpose, and plug it up too, but all of that in the future episodes. This hull will have a 20 cm upper edge on it that will reach the end of the rectangular pipes that are hanging over the edge of the existing tub (just like on the picture in the beginning of the video). These will create mudguards for the wheels / tracks, and more buoyancy too. I will add actual mud flaps in the rear since the wheels are the most out reaching points of the vehicle. And that is on purpose - when I got the chance to drive the Canadian ARGO 8x8 extreme terrain vehicle I noticed I got stuck on the protruding nose all the time when trying to leave a small stream over a steep bank. The first to reach the ground was always the nose. So while designing my own tracked amphibious vehicle I decided to make the wheels/tracks the most protruding features on this handmade DIY offroad all terrain / extreme terrain amphibious vehicle so I would never get stuck again. But all of that will be put on test when my own tracked amphibious vehicle is finally ready to be tested. My vehicle, as the ARGO didn't, has no suspension. Why? It will run very slowly, it's a crawler. I can't say the ride will be very pleasant, but deflating the tires a bit in the middle (the idler wheels) will help to soften the ride a little. Also having less moving parts outside in the mud and water will lower the maintenance cost on this vehicle. Why this enormous ugly looking crash bar / roll bar? So I don't get trapped / squashed by the capsized vehicle. Oh, why is it so TALL? I'm a tall guy, a taller crash bar makes it easier to navigate the inside of the vehicle under the crash bar when on water, under the roof. And the removable roof will be supported by the crash bar too. Why the roof? For protection against the elements during Fall and Winter to make using the vehicle more pleasant. When snowplowing with ATV I've always missed weather protection. So this problem should be solved after this build is finished. Thank you for watching and stay tuned for future episodes!
#donndiy #homemade #trackedvehicle
This video is part of a series of videos, check out the series here: eepost.info/my/video/2IZ3m3N6gayd0o8.html
Check out my other videos on my channel page: eepost.info
Soundtrack:
Pomade - Silent Partner (EEpost Audio Library)
Welding equipment borrowed from Spetselektroodi AS, Estonia:
Fronius TransSteel 2700 welder
Optrel Crystal 2.0 Welding Helmet
Hypertherm Powermax 45 XP plasma cutter

Kommentaarid
Donn DIY
Donn DIY Aasta tagasi
This video is part of a series of videos, check out the series here: eepost.info/face/PLkmF7FAZBzkWdzAxcrnz-WJbzSRyqrSBt Subscribe for more and check out my other videos on my channel page: eepost.info Welding equipment borrowed from Spetselektroodi AS, Estonia: Fronius TransSteel 2700 welder Optrel Crystal 2.0 Welding Helmet Hypertherm Powermax 45 XP plasma cutter
Apoardogan Ali
Apoardogan Ali 8 місяців tagasi
I am an Arab who loves your industry
William Glaser
William Glaser Aasta tagasi
@Jhonatan Luiz Castro Diletti Part 17 will be tomorrow, As last week none due to the holidays!
Jhonatan Luiz Castro Diletti
Jhonatan Luiz Castro Diletti Aasta tagasi
PART 17??????
William Glaser
William Glaser Aasta tagasi
@x111 There are a lot of tracked units that do not have suspension, Argos for example do not! This will be mostly tire suspension due to air pressure. Suspension adds a lot more to the build...
x111
x111 Aasta tagasi
but why do you have zero suspension !!
DrBill
DrBill 6 місяців tagasi
Working at Electric Boat all the welds on the pressure hull were X-Rayed during 3rd shift. If they found bubbles in any welds the welds were ripped out and done over. I would hear the welders brag about how many pounds of welding rods they went through on their shift.
أسامة أنس
أسامة أنس 7 місяців tagasi
رجل مبدع ويحب العمل ولديه صبر طويل . سلمت يداك💪👌👍👏
Jean-Marc Fournier
Jean-Marc Fournier 8 місяців tagasi
It seems that there is no suspension system planned ?
Apoardogan Ali
Apoardogan Ali 8 місяців tagasi
I am an Arab who loves your industry
Валентин Яценко
Валентин Яценко 9 місяців tagasi
Ну просто красава,смотрел бы на это вечность
Quentynn MacPhee
Quentynn MacPhee 10 місяців tagasi
Looks good man, word of advice though, when you're welding, especially on the hull, try to get seams in one shot if possible. The more starts and stops you have, the more prone you are to leaking and the welds possibly failing. No judgment man just some helpful advice from a career welder!
Rodrigo
Rodrigo 10 місяців tagasi
Tá parecendo um carro anfíbio. 👍
Henri Naths
Henri Naths 10 місяців tagasi
Be sure to have a bilge pump on board 😁. Looking good !! ... Those ceramic flapper disc can polish up the welds and make them look like they were made from one price of metal..
Henri Naths
Henri Naths 10 місяців tagasi
Donn DIY I don't think so either. I Didn't see too many oops lol.👍😉
Donn DIY
Donn DIY 10 місяців tagasi
Bilge pump will be installed. However, I think I will not need it.
Henri Naths
Henri Naths 10 місяців tagasi
Nice shop floor. What material is it ?
Henri Naths
Henri Naths 10 місяців tagasi
Donn DIY it look so well done I could not tell. It's been very well taken care of.
Donn DIY
Donn DIY 10 місяців tagasi
Concrete.
Jon Flanagin
Jon Flanagin 11 місяців tagasi
Are you going to add support to the center axles?
osvaldo torres
osvaldo torres 11 місяців tagasi
Ooooman is looking so good 👍 👍 I like it. God bless you
Сергей Ткачёв
Сергей Ткачёв 11 місяців tagasi
Работает один и слесарь и сварщик плюс консртуктор и оператор и ещё даже не знаю сколько всего ОН умеет и знает как и что делать. Про таких говорят КУЛИБИН .
osvaldo torres
osvaldo torres 11 місяців tagasi
Oooman is looking so good 👍.. I like alot .. God bless
Mark Hall
Mark Hall 11 місяців tagasi
After following your videos on this build I would dare say any industry wanting to build or who currently build amphibious vehicles needs to SERIOUSLY EXAMINE YOUR WORK. Some may say you are overbuilding this machine. I say you are building it to the HIGHEST LEVEL of engineering principles and workmanship. It is an absolute DELIGHT to watch you work. Thank you!
MrCebalca
MrCebalca Aasta tagasi
what happened with the episode 17
Alf Iversen
Alf Iversen Aasta tagasi
At this point I hope your wheel alignment is spot on. I don’t see any way of adjusting that or tension?
Серый 1972 Дым-47
Серый 1972 Дым-47 Aasta tagasi
Привет куда пропал
Zoltan Juhasz
Zoltan Juhasz Aasta tagasi
ep.17 pls!!!!!!
Tailss1
Tailss1 Aasta tagasi
With that many seams, eccentric angles and joints you are going to have to apply some sort of waterproofing material to the outside of that hull (something sprayed perhaps) otherwise you will have pinhole leaks that will be a nightmare to sort out. Looking good however can't wait to see it in use. :D
VISHNU- പ്രസാദ്
VISHNU- പ്രസാദ് Aasta tagasi
*Hello bro where are you? What happened? why delay on uploading new part? im eagerly Waiting for your next video part*
عباس الحسناوي
عباس الحسناوي Aasta tagasi
احسنت صنعا
Asssd Sky
Asssd Sky Aasta tagasi
whrer are you this week
Asssd Sky
Asssd Sky Aasta tagasi
thank you
Donn DIY
Donn DIY Aasta tagasi
Dealt with personal matters. Not an interesting subject, I know. 😉
Loshko86
Loshko86 Aasta tagasi
wow, there's still a lot to do on this.. well i have to subscribe then X3
Tiago Moura
Tiago Moura Aasta tagasi
Cadê o vídeo dessa semana??? Ansioso aki... forte abraço
Jani Alanko
Jani Alanko Aasta tagasi
Tere hommikust! It is saturdaymorning and still no new video?? 😵
Jani Alanko
Jani Alanko Aasta tagasi
@Donn DIY sorry, didn't meant to be rude. Take your time. Hope you get things sorted.
Donn DIY
Donn DIY Aasta tagasi
Nope. Dealt with personal matters.
Rahamtullah Mansuri
Rahamtullah Mansuri Aasta tagasi
Donn no video this week?
Айшат Рахматуллаева
Айшат Рахматуллаева Aasta tagasi
Вчера была пятница а видео не было
Andrew Scheepers
Andrew Scheepers Aasta tagasi
I have truly loved watching this series. Can't wait for episode 17
Matus K
Matus K Aasta tagasi
Lunokhod
Spartak Ruiz
Spartak Ruiz Aasta tagasi
Very nice guy!
John Kinnane
John Kinnane Aasta tagasi
G’day Donnwell done mate she’s looking great. John
Joseph D'Angelo
Joseph D'Angelo Aasta tagasi
Hell yeah butter that Edge
Joseph D'Angelo
Joseph D'Angelo Aasta tagasi
Hey what's up brother haven't talked to you in awhile but I can understand you trying to get as comfortable as you can with all that welding to do
Shahid Khan
Shahid Khan Aasta tagasi
Moon car water and buletfroop its going firever strate dariction.
Bobby Tectalabyss
Bobby Tectalabyss Aasta tagasi
Looks great ! Liked,Shared,Add to playlists. All my best.
Karl Joonas
Karl Joonas Aasta tagasi
Vägev. Ei jõua ära oodata millal hääled sisse saab :)
D Herauf
D Herauf Aasta tagasi
Lookin" great and nice welding my friend. I was a maintenance worker for a company in a welding shop for 17 years ! :-) Dennis
Atvsrawsome
Atvsrawsome Aasta tagasi
Building this thing must really be a grind.....
Atvsrawsome
Atvsrawsome Aasta tagasi
Painting the inside is going to be a bitch hahaha
Jim Shue
Jim Shue Aasta tagasi
Your one hell of we fitter young man !
Офтандил Калашников
Офтандил Калашников Aasta tagasi
Будет очень жёсткий ход и тормоза будут сильно греться.
Riduan Sulaiman
Riduan Sulaiman Aasta tagasi
Nice job Donn, have breaks in between weldings. Concern😁😁😁
DIDACT
DIDACT Aasta tagasi
Just noticed this thing has no suspension. Going to be a pretty rough ride when it's finished.
Donn DIY
Donn DIY Aasta tagasi
Just like an ARGO.
Rob N
Rob N Aasta tagasi
How many hours of just welding do you think you have on this project.
Donn DIY
Donn DIY Aasta tagasi
I'm not sure. A lot.
Joseluis Riga
Joseluis Riga Aasta tagasi
looking good...!
Robert Hawthorne
Robert Hawthorne Aasta tagasi
Give this thing a exterior of LineX
guilerdorn
guilerdorn Aasta tagasi
Will you painted it at the end ?
علي الشيخ
علي الشيخ Aasta tagasi
شكرا اخي انا مستمتع في مشاهدتك
denis gomez solla
denis gomez solla Aasta tagasi
Why you clean the weld whith a metal brush if you doens¨t use electrode ?
Alex Alex
Alex Alex Aasta tagasi
Cool looks, a mix of Mad Max and high tech.
Сергей Логвиненко
Сергей Логвиненко Aasta tagasi
корыто с колесами
3loypingvin
3loypingvin Aasta tagasi
when the test?
James Cleveley
James Cleveley Aasta tagasi
I might have missed it, and I'm sure someone has already asked the question, but what is the plan for tensioning the tracks?
Anthony Missotten
Anthony Missotten Aasta tagasi
Encore un beau travail !!!
Rahamtullah Mansuri
Rahamtullah Mansuri Aasta tagasi
Pretty good
Przemekk090
Przemekk090 Aasta tagasi
Is it a New Elon Musk's Tesla car?
Олег Богданович
Олег Богданович Aasta tagasi
то буде танк
Fernando Garcia
Fernando Garcia Aasta tagasi
It has better design than the cybertruck, i guess you could sell it for 39900 usd
Donn DIY
Donn DIY Aasta tagasi
😁
Mel Wilson
Mel Wilson Aasta tagasi
Will it Blend and Will it Float? That is the question....
Mel Wilson
Mel Wilson Aasta tagasi
This is the SV SEEKER of origami amphibs WOW! How much wire and gas is being used in this build? Grind it and it will float ;)
steve lecain
steve lecain Aasta tagasi
your craftsmanship is amazing you have boat loads of talent young man this build has me excited to see the end result.bravo !!
AlfreDoG
AlfreDoG Aasta tagasi
We already know what Elon Musk was inspired to design the Tesla Cibertruck
АЛЕКСАНДР 31
АЛЕКСАНДР 31 Aasta tagasi
*Классно👍🚜*
ross skeller
ross skeller Aasta tagasi
You are actually very artistic and have applied your skills and imagination to make these videos. Well done.
Дядя Вова
Дядя Вова Aasta tagasi
Если после всей работы, эта штука не поедет, я с горя забухаю!
TheTwister3000
TheTwister3000 Aasta tagasi
In cooperation with Tesla?
Matt Courty
Matt Courty Aasta tagasi
Always keeps me coming back for more! Can't wait to see it finished!
Laxpowertoo
Laxpowertoo Aasta tagasi
The thing I drove had a drain valve between my feet that sat flush with the underneath, so any water that came in could be emptied out as soon as you hit dry land without even having to stop. It was held it place by an over centre catch.
de Jaeger Simon
de Jaeger Simon Aasta tagasi
why don't you use TIG welding for this part of the projet? thanks!
Urmo Prants
Urmo Prants Aasta tagasi
de Jaeger Simon It would take much more time to weld.
Alexandr Maloletko
Alexandr Maloletko Aasta tagasi
👍👍👍
Kareem
Kareem Aasta tagasi
Gyro Gearloose (Leidur Leo) couldn't do it better.
tom aguilar
tom aguilar Aasta tagasi
too much soldering footage.
tayler sampson
tayler sampson Aasta tagasi
How is the axle going to work for turning
Daniel Michaud
Daniel Michaud Aasta tagasi
I see where you installed grease fitting, it seems difficult to access. Why not install a small tube and weld it to the bearing housing you want to grease and install the grease fitting at the other end, and you install it at a place where it is easier to access.
g2macs
g2macs Aasta tagasi
For some reason I keep on seeing in my head, some black and white footage of a herd of T34's coming over a hill at Kursk.
Mike Makuh
Mike Makuh Aasta tagasi
How many pounds of wire did that take?????????????
Иван Ивановы
Иван Ивановы Aasta tagasi
Молодец только купить новый маски
عابر سبيل
عابر سبيل Aasta tagasi
صلو على محمد عليه الصلاة والسلام مبدع نتظر متى تخلص اوجعننا عيوننا من اللحام
Terry Shanks
Terry Shanks Aasta tagasi
excellent WELDING! Very neatly done. Do you get many burns? How are your eyes doing? I would worry about them.
Urmo Prants
Urmo Prants Aasta tagasi
Terry Shanks He is using the best welding helmet on the market. Optrel Crystal 2.0. So you shoudn’t be worries about his eyes :)
o0julek0o
o0julek0o Aasta tagasi
This is just so you can brag about your welding skills isn't it! Well my dad is bigger than yours!
Pine Stumps
Pine Stumps Aasta tagasi
Any worry of slip with a single drive wheel? I guess you could always bolt teeth and tube the tire if it came down to it. Looking good as always 👍
Mainer
Mainer Aasta tagasi
I work in a shipyard and we must comply with a "35 foot" rule for all hot-work. All combustible material within that a 35 foot sphere must be removed or protected.
Miguel Benito Ibañez
Miguel Benito Ibañez Aasta tagasi
You are the Mourinho of welding ( The number one). Very Good welding.
Joseph H.
Joseph H. Aasta tagasi
Its been a great build so far and I have enjoyed watching it. But why is the body so much narrower than the track? My first thought was how you could gain much buoyancy by making the sponsons on each side connect across all four wheels, and then I thought how the whole body could be pushed out even easier.
안경환
안경환 Aasta tagasi
This vehicle looks like Tesla truck :)
Юрий Гашков
Юрий Гашков Aasta tagasi
Привет все очень хорошо но средние оси тоже нужно закрыть лишний объем не помешает до меня после дошло но все было окрашено
Fernan du
Fernan du Aasta tagasi
Mucha soldadura
prancstaman
prancstaman Aasta tagasi
Paint a shark mouth on front, LOL.
Рамиль Хасаншин
Рамиль Хасаншин Aasta tagasi
Капли для глаз в конце видео ссылка
Jimmy B's
Jimmy B's Aasta tagasi
You are a man of infinite patience. Copious, legendary patients.
сергей бабакаев
сергей бабакаев Aasta tagasi
Когда уже у надо достроить достал уже
Bryce Ellison
Bryce Ellison Aasta tagasi
Awesome project! You sir have way more patience than I do. I would have never attempted a project like this.
Nick Peterson
Nick Peterson Aasta tagasi
Lookin good and making progress
robociock
robociock Aasta tagasi
This project is so well made to last but u dont know how it will be to ride
66singleman
66singleman Aasta tagasi
no jealous control freak girlfriend or wife bitching in the background..man just keeps grinding and welding
МФ ЕК
МФ ЕК Aasta tagasi
Hea päev. Palun tehke subtiitrid.
GAR_ AGE 29
GAR_ AGE 29 Aasta tagasi
Заибал ты уже 3 серию все обшивать, не интересно уже, давай че нить новое
Total let go
Total let go Aasta tagasi
👍
paul martin
paul martin Aasta tagasi
Always interesting watching a true craftsman do his thing! Pretty good. Peace from Australia 🇦🇺🇦🇺🦘🦘🍺🍺🍺🍺🦘🦘🇦🇺🇦🇺
Making mobile Gas-Powered Belt Conveyor
23:42
Made in Poland
Vaatamised 1,9 mln
GAZ 24 Restoration
47:36
Мастерская RCM
Vaatamised 2,5 mln
Making Lathe MILLING Attachment
13:43
Made in Poland
Vaatamised 2,8 mln
Buggy tank. Installing tracks. ENG SUB
13:58
GoryashchiyeKlyuchi
Vaatamised 375 tuh
Widening Steel Rims - 4x4 Build Ep.3
20:53
Donn DIY
Vaatamised 1,9 mln
Homemade Roller Bender - Make A Metal Bender
18:35
Meanwhile in the Garage
Vaatamised 4,3 mln
Нашли IMac Apple, скульптуры на брошенном складе.
19:51
АУКЦИОН КОНТЕЙНЕРОВ В США
Vaatamised 456 tuh
"Smartphones are Boring now."
12:45
Mrwhosetheboss
Vaatamised 1,4 mln
DID WE GET OUR DREAM HOUSE ?
14:56
The Norris Nuts
Vaatamised 2 mln
The FIRST MKBHD Product: ICONS!
8:39
Marques Brownlee
Vaatamised 1,3 mln